RFI Emission OS-214plus Bedienungsanleitung

DESKTOP BARCODE PRINTER OS-214plus/OS-2140D/ OS-2140/OS-2140Z/ OS-2140DZ/OS-2140E User’s Manual 9001283 (A) - ENG Website: http://www.satoame

17 Media Compartment Release LeverPrint Head Module Release Lever Ribbon Supply Holder 18 4. Unwrap the ribbon roll pac

19 7. Turn back the print head module and then insert the bare core into the pick-up holder. (First snap in the left side, and then the right side.)

21 Loading Media The OS-214plus/OS-2140D/OS-2140/OS-2140Z/OS-2140DZ/ OS-2140E printers offer Two different loading modes: standard or with a cutter.

23 4. Click the media hanger back into the media compartment. 5. Align the media roll to the left end. 6. Move the shield from right to left until

25 10. Put the print head module down and press down firmly until you hear a snap. 11. Close the top cover and turn on the printer or press the "

27 11. Close the top cover and turn on the printer or press the "FEED" button if the printer is already on. Note: The "FEED" but

29 Resetting to Factory Default Settings 1. Turn on the printer and wait for 5 or more seconds. 2. Press the "Feed" button for 10 seconds,

31 Serial (RS-232) Interface Requirements The required cable must have a nine-pin "D" type male connector on one end, which is plugged into

33 Parallel Interface Requirements The required cable (IEEE 1284-compliant is recommended) must have a standard 36-pin parallel connector on one end,

35 Ethernet Status/Activity Indicators LED Status Description Both Off No Ethernet link detected Speed LED Green LED On: 100 Mbps link

1 Proprietary Statement This manual contains proprietary information of Argox Information Co., Ltd. It is intended solely for the information and use

37 USB port on the printer and on the PC. 2. Turn on the printer. If the printer supports Plug-and-Play, and you have successfully connected it usin

39 Then click “Next.” Argox OS-2140 PPLA 40 6. Enter Printer name (i.e. Argox OS-2140 PPLA) and select "do not share this printer

41 7. Check all the data on the showing screen, if it is correct, click "Finish". Argox OS-2140 PPLAArgox OS-2140 PPLA USB

43 9. After driver installation is complete, click "Close". The driver should now be installed. Installed printer Argox OS-2140 PPLA 4

45 3. Under OS-2140 product selection prompt, choose Seagull Driver version and then start installation: Instead of the flash prompt above

47 5. Assign the directory to keep Seagull driver, (for example: C:\Seagull) and click "Next". 48 6. Click "Finish&quo

49 7. Select Install printer drivers and Click "Next" 50 8. Select model & emulation - the following

51 9. Select the port of the printer and click "Next". 52 10. Enter Printer name (i.e. Argox OS-2140 PPLA) a

53 11. Check all the data on the showing screen, if it is correct, click "Finish". Argox OS-2140 PPLA Argox OS-2140 PPLAU

55 13. After driver installation is complete, click "Close". The driver should now be installed. Installed printer Argox OS-21

3 For Support For any issues or questions, contact SATO America, Inc. using the contact information shown here. Limitation of liability SATO Corpora

57 LED Indicators: Power and Ready LEDs blink alternately Power LED Ready LED ON OFF OFF ON Possible Problems Solutions Remarks Ribbon out Suppl

59 Miscellaneous If the host shows "Printer Time out" 1. Check if the communication cable (parallel or serial) is connected securely to yo

61 Caring for Your Printer Adhesives and coatings of media can over time transfer onto the printer components along the media path including the ther

63 Special Caution: Warranty of print heads will be void if print head serial number is removed, altered, defected, or made illegible, under ev

65 6. Disassemble the print head and the mounting bracket by releasing screws. 7. Replace with a new print head. Reassemble the print head module in

67 Technical Reference General Specifications Specification OS-2140D OS-2140 OS-214plus Printing method Direct Transfer Direct Transfer/Thermal Tr

69 2D Barcodes OS-2140 & OS-2140D: PPLA/PPLB/PPLZ: MaxiCode, PDF417, Data Matrix (ECC 200 only), QR code, Composite codes OS-214plus: PPLA: PDF-4

71 Fonts, Bar Codes and Graphics Specification The specifications of fonts, bar codes and graphics depends on the printer emulation. The emulations P

73 Printer Programming Language Z, PPLZ Programming Language PPLZ Internal fonts 8 (A~H) fonts with different point size. 8 AGFA fonts: 7 (P~V) fonts

75 Interface Specifications USB Interface This is port complies with USB 2.0 Full Speed. T Connector Terminal Pin Assignment Pin Signal Descrip

5 Media Sensor ...61 Thermal Print Head...

77 Ethernet The following port complies with Ethernet communication. Pin Signal 1 Transmit+ 2 Transmit- 3 Receive+ 4 Reserved

79 Connection with host Host 25S Printer 9P Host 9S Printer 9P(PC or compatible) (PC or compatible) DTR 20 …… 1 DSR DTR 4 …… 1 DSR DSR 6

81 Appendix I - Installing the Cutter 1. Turn off the printer power and unplug the power cable and Serial / USB cable. 2. Remove the top cover. 3.

83 6. Secure the four screws attaching the cutter. 7. Plug the cutter's connector into the PCB's header connector (J9). 8

85 4. Remove the middle cover. Slot for Extension card 86 5. Mount the extension card to J14 on the main board. 6. Click back the

7 Package Contents  Printer  Power Supply  Power Cord  Quick Installation Guide  CD ROM  USB Cable  0.5” ID Core for Ribbon  Media

9 OS-2140E Power Cord10 OS-214plus

11 Getting to Know Your Printer The illustrations that follow describe the printer’s parts, features, controls, and indicators. Parts and Features

13 Power Switch Ribbon Supply Holder Thermal Print head Platen Roller 14 Controls and Indicators The printer’s controls and indi

15 Control / Indicator Function Power Switch  On: turns on normal operation  Off: turns off power Note: Turn power off before connecting or disc