RFI Emission OS-214plus Bedienungsanleitung

Argox OS-214ZIP Printer User Manual

Loading the Media 8. Turn the wheel of the print head module to ensure the ribbon is tightly wound. 9. Press down the print head module firmly till y

2. Remove the media hanger. 4. Click the media hanger back to the media compartment. 3. Load the media roll onto the hanger from the left. 5. Move t

7. Unlatch the print head module. 10. Turn back the print head module and then press it down firmly till you hear a snap. 8. Hold the print head modu

Peel Off Mode 10. Trim the edge of the label backing paper with scissor or knife. 11. Lead the backing paper over the dispenser bar, then thread it ba

12. Press "FEED" button and the label backing paper will come out from the slot under the H cover. 15. Close the top cover and turn on the p

Cutter Mode 11. Close the top cover and turn on the printer or press the "FEED" button if the printer is already on. ( Installing the cutter

Operator Controls Power Switch Controls printer power On-normal operation Off-the power should be turned off before connect or disconnect the

Performing Calibration Resetting the Printer to Factory Default Settings 1. Keep pressing the feed button while turning on the power, until the pr

Hooking up the Printer and Computer 30 OS-204/214/314 Note : Power Jack The power supply barrel connector must be inserted into the power jack on

Parallel Interface Requirements Communicate with the Printer The required cable (IEEE 1284-compliant is recommended) must have a standard 36-pin pa

Proprietary Statement This manual contains proprietary information of Argox Information Co., Ltd. It is intended solely for the information and use of

Installing Driver Notes : 1. If you are just updating your driver, make sure to delete the previous version first. 1. Click the "Start" but

Set the Parameters For Win 98 ▀ Ports After installing the driver, you can follow the path below to set parameters: Prop

▀ Output bin (Accessory setting) Properties menu → click "Paper" → click "more option" → select Enable/without → cutter, peeler →

For Win 2000 ▀ Ports Properties menu → click "Ports" → select the IO port → click "OK" ▀ Paper source (Media type) Back

▀Create a new size For NT 4.0 Printer menu → right click to get pop- ▀Ports up menu Properties menu → click "Ports" → select "Serve

For Win XP ▀ Paper/Output (Speed) ▀ Print quality (Darkness) Default Document menu → Click "Advanced". → Click each item to select desired

46 ▀ Orientation ▀ Create a new size Printer menu Printing Reference menu → Click "Layout". → Right click to get → Select "Portr

Troubleshooting B. Power and Ready LEDs blink alternately Power LED Ready LED ON OFF OFF ONNormally, when the printer is in abnormal condition, th

 Poor printout quality. D. Miscellaneous . The ribbon may not be qualified.  The host shows "Printer Time out" . The media may not be qua

Caring for Your Printer Replacing Thermal Print Head 1. Switch off the power and wait for both LEDs to go off. Clean the following areas of the prin

Page Checking Your Box...1 Power Supply...

Reference Technical Information 1. General Specifications 54Specification Model OS-203DTModel OS-204DTModel OS-214TT Model OS-314T

2. Fonts, Bar Codes and Graphics Specification Ribbon types Ribbon size Wax, Wax/Resin and Resin OD 1.45 in. (37 mm); ID 0.5 in. (12.7mm); Length11 Di

3. Interface Specifications Printer Programming Language B, PPLB Specification Model OS-203DTModel OS-204DT ModelOS-214TTModelOS-314TTGeneral font

Note : The simplest way to connect to other hosts (not PC compatible) or terminals is: Pin 9 on OS-204/214/314 and pin 1 on OS-203 are reserved for KD

Parallel (Centronics) 4. ASCIITABLE The parallel port is a standard 36-pin Centronics. Its pin assignments are listed as following. 62 NUL 0 @

Appendix I - Installing Dispenser Kit 6. Route the peeler sensor cable through the guides along the left side of the top cover. 7. Fix the sensor cab

Middle Cover Base Housing 8. Release the two screws at the bottom of the base housing. 12. Release the screw on the left bracket of the chassis.

16. Hook the dispenser bar on the brackets of the chassis, positioning it above the white roller. Ensure that the dispenser bar is paralleled with the

Appendix II - Installing the Cutter 4. Remove the whole print head assembly by releasing 4 screws at its feet. 1. Turn off the printer power, unplug

5. Add a driver IC to U19 on the main board. 6. Secure four attached screws for the cutter. 7. Plug the cutter's connector into t

Checking Your Box Receiving the box of your printer, you are advised to check first for the possible shipping damage. There are two ways you can d

Power Supply 1. The Power Adapter has a barrel connector on one end that must be inserted into the power jack on the back of the printer. 2. Plug the

Parts and Features (OS-214, OS-314) Power SwitchRibbon Pick-up HolderRelease LeversMedia Hanger Top Cover H Cover PowerIndic

Parts and Features (OS-202 , OS-204) Top CoverThermal Printhead Power SwitchH Cover Power IndicatorReady indicator Feed But

Loading the Ribbon (OS-214, OS-314) Media Compartment Note: This section is not applicable to the direct thermal printing. 1. Lift the top cover to

4. Unwrap the ribbon roll pack and separate the ribbon roll and the bare core. 7. Turn back the print head module and then insert the bare core into t